C-360の起動ログ

arista-c360.log

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00163
S - IMAGE_VARIANT_STRING=HAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e1
B -       201 - PBL, Start
B -      2736 - bootable_media_detect_entry, Start
B -      2882 - bootable_media_detect_success, Start
B -      2887 - elf_loader_entry, Start
B -     11391 - auth_hash_seg_entry, Start
B -     49576 - auth_hash_seg_exit, Start
B -    289183 - elf_segs_hash_verify_entry, Start
B -    349865 - PBL, End
B -    549884 - SBL1, Start
B -    628727 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    638578 - pm_device_init, Start
B -    822097 - PM_SET_VAL:Skip
D -    181597 - pm_device_init, Delta
B -    824537 - pm_driver_init, Start
D -      5368 - pm_driver_init, Delta
B -    830881 - clock_init, Start
D -      2135 - clock_init, Delta
B -    834815 - boot_flash_init, Start
D -      3782 - boot_flash_init, Delta
B -    842379 - boot_config_data_table_init, Start
D -      1006 - boot_config_data_table_init, Delta - (575 Bytes)
B -    852383 - Boot Setting :  0x00001618
B -    856104 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:8
B -    863028 - sbl1_ddr_set_params, Start
B -    866840 - CPR configuration: 0x30c
B -    870287 - cpr_init, Start
B -    873062 - Rail:0 Mode: 5 Voltage: 800000
B -    878278 - CL CPR settled at 752000mV
B -    881114 - Rail:1 Mode: 5 Voltage: 880000
B -    885293 - Rail:1 Mode: 7 Voltage: 896000
D -     16531 - cpr_init, Delta
B -    892186 - Pre_DDR_clock_init, Start
B -    896212 - Pre_DDR_clock_init, End
B -    899506 - DDR Type : PCDDR4
B -    906399 - do ddr sanity test, Start
D -      1067 - do ddr sanity test, Delta
B -    910028 - DDR: Start of HAL DDR Boot Training
B -    914756 - DDR: End of HAL DDR Boot Training
B -    920459 - DDR: Checksum to be stored on flash is -774473841
B -    930768 - Image Load, Start
D -    619638 - QSEE Image Loaded, Delta - (1382936 Bytes)
B -   1550498 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -   1558153 - Image Load, Start
D -    293532 - DEVCFG Image Loaded, Delta - (32548 Bytes)
B -   1851777 - Image Load, Start
D -    309880 - RPM Image Loaded, Delta - (93060 Bytes)
B -   2161748 - Image Load, Start
D -    429928 - APPSBL Image Loaded, Delta - (602530 Bytes)
B -   2591798 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -   2597624 - USB D+ check, Start
D -         0 - USB D+ check, Delta
B -   2603998 - SBL1, End
D -   2056432 - SBL1, Delta
S - Flash Throughput, 4428 KB/s  (2112321 Bytes,  477011 us)
S - DDR Frequency, 533 MHz
S - Core 0 Frequency, 1651 MHz


U-Boot 2016.01 (Feb 22 2024 - 07:45:27 +0000)

DRAM:  smem ram ptable found: ver: 1 len: 4
2 GiB
NAND:  Could not find nand_gpio in dts, using defaults
ONFI device found
ID = 2690a32c
Vendor = 2c
Device = a3
qpic_nand: changing oobsize to 160 from 224 bytes
SPI_ADDR_LEN=3
SF: Detected MX25U25635F with page size 256 Bytes, erase size 64 KiB, total 32 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x2000000
1056 MiB
MMC:   <NULL>: 0
PCI Link Intialized
PCI Link Intialized
In:    serial@78B3000
Out:   serial@78B3000
Err:   serial@78B3000
SENAO 74LV164 SHIFT LED INIT!
machid: 8010008
Card did not respond to voltage select!
Net:   MAC0 addr:30:86:2d:81:44:3f
SPI_ADDR_LEN=3
SF: Detected MX25U25635F with page size 256 Bytes, erase size 64 KiB, total 32 MiB
device 0 offset 0x790000, size 0x80000
SF: 524288 bytes @ 0x790000 Read: OK
CRC check good on phy fw file (0xC359)
PHYFW:Loading IRAM...........done.
PHYFW:Loading DRAM..............done.
phy fw image load good CRC-16 matches (0xBC9C)
PHY ID1: 0x31c3
PHY ID2: 0x1c12
SPI_ADDR_LEN=3
SF: Detected MX25U25635F with page size 256 Bytes, erase size 64 KiB, total 32 MiB
device 0 offset 0x790000, size 0x80000
SF: 524288 bytes @ 0x790000 Read: OK
CRC check good on phy fw file (0xC359)
PHYFW:Loading IRAM...........done.
PHYFW:Loading DRAM..............done.
phy fw image load good CRC-16 matches (0xBC9C)
PHY ID1: 0x31c3
PHY ID2: 0x1c12
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0
SPI_ADDR_LEN=3
SF: Detected MX25U25635F with page size 256 Bytes, erase size 64 KiB, total 32 MiB
device 0 offset 0x810000, size 0x800000
SF: 8388608 bytes @ 0x810000 Read: OK
It is not a elf image

## Checking Image at 44000000 ...

Unknown image format, try again after offsetting for MBN header
## Checking Image at 44000028 ...
   FIT image found
   FIT description: ARM64 OpenWrt FIT (Flattened Image Tree)
    Image 0 (kernel@1)
     Description:  ARM64 OpenWrt Linux-4.4
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x4400010c
     Data Size:    4050463 Bytes = 3.9 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x41080000
     Entry Point:  0x41080000
     Hash algo:    crc32
     Hash value:   e6729ec8
     Hash algo:    sha1
     Hash value:   f04fe6e08bb2d67450fae36017ec7ac79c59c489
    Image 1 (fdt@hk09)
     Description:  ARM64 OpenWrt qcom-ipq807x-hk09 device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x443dd074
     Data Size:    85844 Bytes = 83.8 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   a6bf1e04
     Hash algo:    sha1
     Hash value:   f6c0f4424b72941455dd6c87285706e0e3b4a88a
    Default Configuration: 'config@hk09'
    Configuration 0 (config@hk09)
     Description:  OpenWrt
     Kernel:       kernel@1
     FDT:          fdt@hk09
## Checking hash(es) for FIT Image at 44000028 ...
   Hash(es) for Image 0 (kernel@1): crc32+ sha1+
   Hash(es) for Image 1 (fdt@hk09): crc32+ sha1+
Saving Environment to SPI Flash...
Erasing SPI flash...Writing to SPI flash...done
Secure boot: enabled
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "mtd=0", size 384 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 1536, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 5/3, WL threshold: 4096, image sequence number: 70393936
ubi0: available PEBs: 0, total reserved PEBs: 1536, PEBs reserved for bad PEB handling: 80
Read 0 bytes from volume rootfs_sig to 44000000
No size specified -> Using max size (6440)
ubi0: detaching mtd2
ubi0: mtd2 is detached
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "mtd=0", size 384 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 1536, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 5/3, WL threshold: 4096, image sequence number: 70393936
ubi0: available PEBs: 0, total reserved PEBs: 1536, PEBs reserved for bad PEB handling: 80
Read 49142664 bytes from volume ubi_rootfs to 42000028
Rootfs image authentication successful
SPI_ADDR_LEN=3
SF: Detected MX25U25635F with page size 256 Bytes, erase size 64 KiB, total 32 MiB
device 0 offset 0x810000, size 0x800000
SF: 8388608 bytes @ 0x810000 Read: OK
Kernel image authentication successful
## Loading kernel from FIT Image at 44000028 ...
   Using 'config@hk09' configuration
   Trying 'kernel@1' kernel subimage
     Description:  ARM64 OpenWrt Linux-4.4
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x4400010c
     Data Size:    4050463 Bytes = 3.9 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x41080000
     Entry Point:  0x41080000
     Hash algo:    crc32
     Hash value:   e6729ec8
     Hash algo:    sha1
     Hash value:   f04fe6e08bb2d67450fae36017ec7ac79c59c489
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000028 ...
   Using 'config@hk09' configuration
   Trying 'fdt@hk09' fdt subimage
     Description:  ARM64 OpenWrt qcom-ipq807x-hk09 device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x443dd074
     Data Size:    85844 Bytes = 83.8 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   a6bf1e04
     Hash algo:    sha1
     Hash value:   f6c0f4424b72941455dd6c87285706e0e3b4a88a
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x443dd074
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 4a3e8000, end 4a3fff53 ... OK
Using machid 0x8010008 from environment

Starting kernel ...

Jumping to AARCH64 kernel via monitor
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] Ignoring memory range 0x40000000 - 0x41000000
[    0.000000] Machine: Qualcomm Technologies, Inc. IPQ807x/AP-HK09
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000057f00000, size 24 MiB
[    0.000000] Reserved memory: initialized node dma_pool0@57f00000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000059700000, size 24 MiB
[    0.000000] Reserved memory: initialized node dma_pool1@59700000, compatible id shared-dma-pool
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] PERCPU: Embedded 15 pages/cpu @ffffffc07ef43000 s20736 r8192 d32512 u61440
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 442511
[    0.000000] Kernel command line: console=ttyMSM0,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait pri=0 swiotlb=1 coherent_pool=2M
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] software IO TLB [mem 0xbfdbc000-0xbfdfc000] (0MB) mapped at [ffffffc07edbc000-ffffffc07edfbfff]
[    0.000000] Memory: 1746868K/1798140K available (5516K kernel code, 655K rwdata, 2368K rodata, 220K init, 2333K bss, 51272K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0040000 - 0xffffffbdc2000000   (    31 MB actual)
[    0.000000]     fixed   : 0xffffffbffa7fd000 - 0xffffffbffac00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000   (    16 MB)
[    0.000000]     modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc07f000000   (  2032 MB)
[    0.000000]       .init : 0xffffffc000836000 - 0xffffffc00086d000   (   220 KB)
[    0.000000]       .text : 0xffffffc000080000 - 0xffffffc000835314   (  7893 KB)
[    0.000000]       .data : 0xffffffc00087b000 - 0xffffffc00091ec00   (   655 KB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] Architected cp15 timer(s) running at 19.20MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000469] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000480] pid_max: default: 32768 minimum: 301
[    0.000569] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000579] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.001289] EFI services will not be available.
[    0.001315] ASID allocator initialised with 65536 entries
[    0.052242] MSM Memory Dump base table set up
[    0.052263] MSM Memory Dump apps data table set up
[    0.090053] Detected VIPT I-cache on CPU1
[    0.090097] CPU1: Booted secondary processor [410fd034]
[    0.120041] Detected VIPT I-cache on CPU2
[    0.120069] CPU2: Booted secondary processor [410fd034]
[    0.150066] Detected VIPT I-cache on CPU3
[    0.150093] CPU3: Booted secondary processor [410fd034]
[    0.150141] Brought up 4 CPUs
[    0.150166] SMP: Total of 4 processors activated.
[    0.150176] CPU: All CPU(s) started at EL1
[    0.150199] alternatives: patching kernel code
[    0.167710] DMI not present or invalid.
[    0.167945] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.167970] futex hash table entries: 1024 (order: 5, 131072 bytes)
[    0.168298] pinctrl core: initialized pinctrl subsystem
[    0.169208] NET: Registered protocol family 16
[    0.189998] cpuidle: using governor ladder
[    0.220015] cpuidle: using governor menu
[    0.220214] NET: Registered protocol family 42
[    0.220341] vdso: 2 pages (1 code @ ffffffc000881000, 1 data @ ffffffc000880000)
[    0.220371] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.221054] DMA: preallocated 2048 KiB pool for atomic allocations
[    0.221172] Read of property:soc_version_minor from node failed
[    0.221181] CPU: IPQ8076A, SoC Version: 2.0
[    0.221594] IPC logging disabled
[    0.221600] IPC logging disabled
[    0.221604] IPC logging disabled
[    0.221609] IPC logging disabled
[    0.221613] IPC logging disabled
[    0.224231] Soc version is not 1, changing clock offsets
[    0.235963] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[    0.238311] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[    0.241609] sps:sps is ready.
[    0.246718] spmi spmi-0: PMIC Arb Version-2 (0x20010000)
[    0.253138] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[    0.253451] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[    0.282033] pps_core: LinuxPPS API ver. 1 registered
[    0.282040] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    0.282064] PTP clock support registered
[    0.282212] dmi: Firmware registration failed.
[    0.283916] Bluetooth: Core ver 2.21
[    0.283945] NET: Registered protocol family 31
[    0.283951] Bluetooth: HCI device and connection manager initialized
[    0.283963] Bluetooth: HCI socket layer initialized
[    0.283973] Bluetooth: L2CAP socket layer initialized
[    0.284204] clocksource: Switched to clocksource arch_sys_counter
[    0.287334] NET: Registered protocol family 2
[    0.287960] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.288162] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[    0.288525] TCP: Hash tables configured (established 16384 bind 16384)
[    0.288584] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[    0.288647] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[    0.288849] NET: Registered protocol family 1
[    0.289224] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    0.298676] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.298694] jffs2: version 2.2 (NAND) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.302317] Key type asymmetric registered
[    0.302333] Asymmetric key parser 'x509' registered
[    0.302365] io scheduler noop registered
[    0.302379] io scheduler deadline registered (default)
[    0.304634] 20000000.pci supply vdda not found, using dummy regulator
[    0.304682] 20000000.pci supply vdda_phy not found, using dummy regulator
[    0.304716] 20000000.pci supply vdda_refclk not found, using dummy regulator
[    0.305358] PCI host bridge /soc/pci@20000000 ranges:
[    0.305385]    IO 0x20200000..0x2020ffff -> 0x20200000
[    0.305400]   MEM 0x20220000..0x2fffffff -> 0x20220000
[    0.555742] qcom-pcie 20000000.pci: link up
[    0.555885] qcom-pcie 20000000.pci: PCI host bridge to bus 0000:00
[    0.555899] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.555912] pci_bus 0000:00: root bus resource [io  0x0000-0xffff] (bus address [0x20200000-0x2020ffff])
[    0.555923] pci_bus 0000:00: root bus resource [mem 0x20220000-0x2fffffff]
[    0.556234] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.557146] pci 0000:00:00.0: BAR 8: assigned [mem 0x20400000-0x205fffff]
[    0.557161] pci 0000:00:00.0: BAR 9: assigned [mem 0x20600000-0x207fffff 64bit pref]
[    0.557174] pci 0000:00:00.0: BAR 0: assigned [mem 0x20220000-0x20220fff 64bit]
[    0.557189] pci 0000:00:00.0: BAR 7: assigned [io  0x1000-0x1fff]
[    0.557203] pci 0000:01:00.0: BAR 0: assigned [mem 0x20400000-0x205fffff 64bit]
[    0.557252] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.557262] pci 0000:00:00.0:   bridge window [io  0x1000-0x1fff]
[    0.557273] pci 0000:00:00.0:   bridge window [mem 0x20400000-0x205fffff]
[    0.557284] pci 0000:00:00.0:   bridge window [mem 0x20600000-0x207fffff 64bit pref]
[    0.557335] PCIe: RC0 enabled during bootup
[    0.557546] 10000000.pci supply vdda not found, using dummy regulator
[    0.557595] 10000000.pci supply vdda_phy not found, using dummy regulator
[    0.557652] 10000000.pci supply vdda_refclk not found, using dummy regulator
[    0.558202] PCI host bridge /soc/pci@10000000 ranges:
[    0.558223]    IO 0x10200000..0x1020ffff -> 0x10200000
[    0.558236]   MEM 0x10220000..0x1fffffff -> 0x10220000
[    0.805745] qcom-pcie 10000000.pci: link up
[    0.805877] qcom-pcie 10000000.pci: PCI host bridge to bus 0001:00
[    0.805889] pci_bus 0001:00: root bus resource [bus 00-ff]
[    0.805902] pci_bus 0001:00: root bus resource [io  0x10000-0x1ffff] (bus address [0x10200000-0x1020ffff])
[    0.805912] pci_bus 0001:00: root bus resource [mem 0x10220000-0x1fffffff]
[    0.806185] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.807318] pci 0001:00:00.0: BAR 8: assigned [mem 0x10400000-0x105fffff]
[    0.807332] pci 0001:00:00.0: BAR 0: assigned [mem 0x10220000-0x10220fff 64bit]
[    0.807350] pci 0001:01:00.0: BAR 0: assigned [mem 0x10400000-0x105fffff 64bit]
[    0.807415] pci 0001:00:00.0: PCI bridge to [bus 01]
[    0.807426] pci 0001:00:00.0:   bridge window [mem 0x10400000-0x105fffff]
[    0.807482] PCIe: RC1 enabled during bootup
[    0.811790] msm_rpm_log_probe: OK
[    0.812107] msm-dcc b3000.dcc: DCC XPU is not specified
[    0.812351] msm-dcc b3000.dcc: jiffies_64: 0xffff8b20, cntvct_64: 0x2f97631c
[    0.812363] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff8000596004)
[    0.812373] msm-dcc b3000.dcc: gcnt_lo: 0x2f9764df(0xffffff8000596000)
[    0.812952] TZ SMMU State: SMMU Stage2 Enabled
[    0.813009] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set
[    0.814607] msm_serial 78b3000.serial: msm_serial: detected port #0
[    0.814648] msm_serial 78b3000.serial: uartclk = 3686400
[    0.814684] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 78, base_baud = 230400) is a MSM
[    0.814704] msm_serial: console setup on port #0
[    1.772594] console [ttyMSM0] enabled
[    1.777567] msm_serial 78b1000.serial: msm_serial: detected port #1
[    1.780850] msm_serial 78b1000.serial: uartclk = 19200000
[    1.786933] 78b1000.serial: ttyMSM1 at MMIO 0x78b1000 (irq = 79, base_baud = 1200000) is a MSM
[    1.792771] msm_serial: driver initialized
[    1.801262] msm_serial_hsl_init: driver initialized
[    1.805436] diag: IPC Logging disabled
[    1.810334] TRACK: P[0]      PMask[4]
[    1.813626] TRACK: P[1]      PMask[4]
[    1.817026] TRACK: P[2]      PMask[4]
[    1.820518] TRACK: P[3]      PMask[4]
[    1.823492] nik 4097 info->svc_id
[    1.835058] brd: module loaded
[    1.835691] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.837744] spi_qup 78b8000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.845670] m25p80 spi32766.0: found mx25u25635f, expected n25q128a11
[    1.851244] m25p80 spi32766.0: mx25u25635f (32768 Kbytes)
[    1.857726] 25 ofpart partitions found on MTD device spi32766.0
[    1.862956] Creating 25 MTD partitions on "spi32766.0":
[    1.868713] 0x000000000000-0x000000050000 : "0:SBL1"
[    1.874560] 0x000000050000-0x000000060000 : "0:MIBIB"
[    1.879675] 0x000000060000-0x000000080000 : "0:BOOTCONFIG"
[    1.884655] 0x000000080000-0x0000000a0000 : "0:BOOTCONFIG1"
[    1.889998] 0x0000000a0000-0x000000220000 : "0:QSEE"
[    1.895513] 0x000000220000-0x0000003a0000 : "0:QSEE_1"
[    1.900672] 0x0000003a0000-0x0000003b0000 : "0:DEVCFG"
[    1.905638] 0x0000003b0000-0x0000003c0000 : "0:DEVCFG_1"
[    1.910753] 0x0000003c0000-0x0000003d0000 : "0:APDP"
[    1.916232] 0x0000003d0000-0x0000003e0000 : "0:APDP_1"
[    1.921158] 0x0000003e0000-0x000000420000 : "0:RPM"
[    1.926159] 0x000000420000-0x000000460000 : "0:RPM_1"
[    1.930888] 0x000000460000-0x000000470000 : "0:CDT"
[    1.936104] 0x000000470000-0x000000480000 : "0:CDT_1"
[    1.940768] 0x000000480000-0x000000490000 : "0:APPSBLENV"
[    1.946015] 0x000000490000-0x000000590000 : "0:APPSBL"
[    1.951377] 0x000000590000-0x000000690000 : "0:APPSBL_1"
[    1.956419] 0x000000690000-0x000000790000 : "0:ART"
[    1.961885] 0x000000790000-0x000000810000 : "0:ETHPHYFW"
[    1.966499] 0x000000810000-0x000001010000 : "0:HLOS"
[    1.972039] 0x000001010000-0x000001810000 : "0:HLOS_1"
[    1.976996] 0x000001810000-0x000001c10000 : "CONFIG"
[    1.981921] 0x000001c10000-0x000001c30000 : "DEVCERT"
[    1.987061] 0x000001c30000-0x000001c50000 : "RESERVED1"
[    1.992037] 0x000001c50000-0x000002000000 : "RESERVED2"
[    1.998024] QPIC controller hw version Major:1, Minor:5
[    2.001979] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xa3
[    2.006903] nand: ONFI 10-Compliant Micron MT29F8G08ABBCAH4
[    2.013478] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224
[    2.018821] 3 ofpart partitions found on MTD device qcom_nand.0
[    2.026768] Creating 3 MTD partitions on "qcom_nand.0":
[    2.032401] 0x000000000000-0x000018000000 : "rootfs"
[    2.178689] mtd: device 25 (rootfs) set to be root filesystem
[    2.179104] mtdsplit: no squashfs found in "rootfs"
[    2.183411] 0x000018000000-0x000030000000 : "rootfs_1"
[    2.329542] 0x000030000000-0x000040000000 : "LOGGING"
[    2.422470] random: nonblocking pool is initialized
[    2.424560] libphy: Fixed MDIO Bus: probed
[    2.426805] qca-mdio 90000.mdio: Could not find phy-reset-gpio
[    2.430400] libphy: qca_mdio: probed
[    2.437298] qca-mdio 90000.mdio: qca-mdio driver was registered
[    2.440038] tun: Universal TUN/TAP device driver, 1.6
[    2.445534] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[    2.450796] cnss: INFO: IPC Logging is disabled!
[    2.457295] cnss[2]: INFO: Platform driver probed successfully. plat ffffffc07bfc0018 tgt 0xfffe
[    2.461727] cnss[27]: INFO: Platform driver probed successfully. plat ffffffc07bfd0018 tgt 0x1104
[    2.470528] cnss[28]: INFO: Platform driver probed successfully. plat ffffffc07bff8018 tgt 0x1104
[    2.479332] cnss[27]: INFO: PCI device ffffffc07c231800 probed successfully
[    2.488008] cnss[28]: INFO: PCI device ffffffc07c232800 probed successfully
[    2.494801] i2c /dev entries driver
[    2.508644]
[    2.508644] qcom_wdt_scm_fill_log_dump_tlv:  paddr 41923d60 pbytes_addr 41923d20 panic_magic_no 418d37f8
[    2.534435] Bluetooth: HCI UART driver ver 2.3
[    2.534458] Bluetooth: HCI UART protocol H4 registered
[    2.537760] Bluetooth: HCI UART protocol BCSP registered
[    2.543336] sdhci: Secure Digital Host Controller Interface driver
[    2.548369] sdhci: Copyright(c) Pierre Ossman
[    2.554357] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.607688] console [pstore-1] enabled
[    2.607813] pstore: Registered ramoops as persistent store backend
[    2.610326] ramoops: attached 0x800000@0x5f800000, ecc: 0/0
[    2.619027] remoteproc remoteproc0: releasing cd00000.qcom_q6v5_wcss
[    2.623125] SPMI VADC - Min ch: 0 Max ch: 15
[    2.630393] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000
[    2.632898] coresight-csr 6001000.csr: CSR initialized
[    2.640383] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000
[    2.645335] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000
[    2.652837] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000
[    2.660225] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000
[    2.667607] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000
[    2.674985] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000
[    2.682350] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000
[    2.689736] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000
[    2.697123] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000
[    2.704498] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000
[    2.711866] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000
[    2.719254] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000
[    2.726626] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000
[    2.733999] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000
[    2.741386] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000
[    2.748768] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000
[    2.756146] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000
[    2.763514] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000
[    2.770918] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000
[    2.778296] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000
[    2.785682] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000
[    2.793196] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000006044000
[    2.800284] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006044000
[    2.817369] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006044000
[    2.833245] sps:BAM 0x0000000006044000 is registered.[    2.841040] coresight-tmc 6028000.tmc: TMC initialized
[    2.845741] coresight-tmc 6027000.tmc: TMC initialized
[    2.850843] coresight-funnel 6021000.funnel: FUNNEL initialized
[    2.855890] coresight-funnel 6100000.funnel: FUNNEL initialized
[    2.861689] coresight-funnel 6120000.funnel: FUNNEL initialized
[    2.867605] coresight-funnel 6130000.funnel: FUNNEL initialized
[    2.873509] coresight-funnel 61a1000.funnel: FUNNEL initialized
[    2.879903] coresight-etm4x 619c000.etm: ETM 4.0 initialized
[    2.885559] coresight-etm4x 619d000.etm: ETM 4.0 initialized
[    2.891436] coresight-etm4x 619e000.etm: ETM 4.0 initialized
[    2.897113] coresight-etm4x 619f000.etm: ETM 4.0 initialized
[    2.902515] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized
[    2.908137] coresight-stm: probe of 6002000.stm failed with error -1
[    2.916843] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000
[    2.922060] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized
[    2.930746] NET: Registered protocol family 10
[    2.937792] NET: Registered protocol family 17
[    2.941356] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.945800] Bridge firewalling registered
[    2.958514] 8021q: 802.1Q VLAN Support v1.8
[    2.962436] lib80211: common routines for IEEE802.11 drivers
[    2.977969] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[    2.978216] pmd9655_s3: supplied by e-smps1-reg
[    2.984283] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[    2.988594] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[    2.995208] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[    3.002857] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[    3.010384] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[    3.019512] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      SVS: open-loop= 704000 uV
[    3.026459] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      NOM: open-loop= 840000 uV
[    3.036439] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused    TURBO: open-loop= 904000 uV
[    3.046266] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused   STURBO: open-loop= 992000 uV
[    3.056119] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      SVS: quot[ 7]= 722, quot_offset[ 7]=   0
[    3.065871] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      NOM: quot[ 7]= 977, quot_offset[ 7]= 255
[    3.076721] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused    TURBO: quot[ 7]=1080, quot_offset[ 7]= 100
[    3.087659] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused   STURBO: quot[ 7]=1233, quot_offset[ 7]= 150
[    3.098722] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[    3.110066] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[    3.116394] pmd9655_s4: supplied by e-smps1-reg
[    3.123522] cpr3_mem_acc_init: npu: not using memory accelerator regulator
[    3.127845] npu_corner: fused      NOM: open-loop= 792000 uV
[    3.134781] npu_corner: fused    TURBO: open-loop= 856000 uV
[    3.140628] npu_corner: fused      NOM: open-loop= 792000 uV
[    3.146241] npu_corner: fused    TURBO: open-loop= 856000 uV
[    3.151896] npu_corner: Normal and Cold condition init done. Default to normal.
[    3.158500] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz
[    3.164716] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz
[    3.173359] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_q6v5_wcss
[    3.180565] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available
[    3.189225] ubi0: attaching mtd25
[    4.450996] ubi0: scanning is finished
[    4.456234] ubi0: attached mtd25 (name "rootfs", size 384 MiB)
[    4.456254] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[    4.460947] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[    4.467815] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
[    4.474668] ubi0: good PEBs: 1536, bad PEBs: 0, corrupted PEBs: 0
[    4.481433] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    4.487688] ubi0: max/mean erase counter: 5/3, WL threshold: 4096, image sequence number: 70393936
[    4.494810] ubi0: available PEBs: 0, total reserved PEBs: 1536, PEBs reserved for bad PEB handling: 80
[    4.503755] ubi0: background thread "ubi_bgt0d" started, PID 134
[    4.534630] hctosys: unable to open rtc device (rtc0)
[    4.539490] pmd9655_ldo11: disabling
[    4.542392] VFS: Mounted root (squashfs filesystem) readonly on device 31:28.
[    4.542511] Freeing unused kernel memory: 220K (ffffffc000836000 - ffffffc00086d000)
[    4.549386] Freeing alternatives memory: 40K (ffffffc00086d000 - ffffffc000877000)
/etc/preinit PREINIT=
/etc/preinit PREINIT=1
preinit 2
mount: mounting proc on /proc failed: Device or resource busy
mount: mounting sysfs on /sys failed: Device or resource busy
[    6.685456] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 1448
[    6.732822] UBIFS (ubi0:1): recovery needed
[    6.851146] UBIFS (ubi0:1): recovery completed
[    6.851220] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[    6.854496] UBIFS (ubi0:1): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[    6.862384] UBIFS (ubi0:1): FS size: 316424192 bytes (301 MiB, 1246 LEBs), journal size 15745024 bytes (15 MiB, 62 LEBs)
[    6.872285] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[    6.883217] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID FC54DA03-7FAF-4685-972F-5F1F8FB99FA4, small LPT model
[    7.964656] DID VID ffffffc0
[    7.964727] DID VID ffffffd1
[    7.966635] tpm_spi_tis spi32765.0: 2.0 TPM (device-id 0xFFFF, rev-id 22)
[    8.004675] tpm_spi_tis spi32765.0: A TPM error (256) occurred continue selftest
[    8.004699] tpm_spi_tis spi32765.0: Firmware has not started TPM
Kernel Ver 4.x
Executing fopivot_kver_4_x
File-system state: Verified Trusted

[   24.061308] procd: - early -
[   24.061374] procd: - watchdog -
[   24.635697] procd: - watchdog -
[   24.635819] procd: - ubus -
[   24.637897] procd: Started instance ubus::instance1[1589]
[   24.688300] procd: - init -
[   24.701591] INFO: Starting coredump setup
[   24.701727] INFO: coredump setup complete

 (none) aarch64 #1 SMP PREEMPT Mon Jun 10 10:47:17 UTC 2024 (none)
(none) login: [   25.088058] jffs2: notice: (1714) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.