FLSUN_SR_Prusa.ini

[printer:FLSun Super Racer]
bed_custom_model =
bed_custom_texture =
bed_shape = 129.505x11.3302,128.025x22.5742,125.57x33.6464,122.16x44.4626,117.82x54.9403,112.583x64.9999,106.49x74.5649,99.5857x83.5623,91.9238x91.9238,83.5623x99.5857,74.5649x106.49,65x112.583,54.9403x117.82,44.4626x122.16,33.6464x125.57,22.5742x128.025,11.3302x129.505,7.9602e-15x130,-11.3302x129.505,-22.5742x128.025,-33.6464x125.57,-44.4626x122.16,-54.9403x117.82,-64.9999x112.583,-74.5649x106.49,-83.5623x99.5857,-91.9238x91.9238,-99.5857x83.5623,-106.49x74.5649,-112.583x65,-117.82x54.9403,-122.16x44.4626,-125.57x33.6464,-128.025x22.5742,-129.505x11.3302,-130x1.59204e-14,-129.505x-11.3302,-128.025x-22.5742,-125.57x-33.6464,-122.16x-44.4626,-117.82x-54.9403,-112.583x-65,-106.49x-74.5649,-99.5857x-83.5623,-91.9238x-91.9238,-83.5623x-99.5857,-74.5649x-106.49,-65x-112.583,-54.9403x-117.82,-44.4626x-122.16,-33.6464x-125.57,-22.5742x-128.025,-11.3302x-129.505,-2.38806e-14x-130,11.3302x-129.505,22.5742x-128.025,33.6464x-125.57,44.4626x-122.16,54.9403x-117.82,64.9999x-112.583,74.5649x-106.49,83.5623x-99.5857,91.9238x-91.9238,99.5857x-83.5623,106.49x-74.5649,112.583x-64.9999,117.82x-54.9403,122.16x-44.4626,125.57x-33.6464,128.025x-22.5742,129.505x-11.3302,130x-3.18408e-14
before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
between_objects_gcode =
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Generic PLA FLSUN"
default_print_profile = 0.20mm QUALITY FLSUN
deretract_speed = 40
end_gcode = M107 T0\nM104 S0\nM104 S0 T1\nM140 S0\nG92 E0\nG91\nG1 E-1 F300\nG1 Z+0.5 E-5 F6000\nG28 X0 Y0\nM84 ;steppers off\nG90 ;absolute positioning
extra_loading_move = -2
extruder_colour = ""
extruder_offset = 0x0
gcode_flavor = reprapfirmware
high_current_on_filament_swap = 0
host_type = octoprint
inherits = FLSun QQS Pro
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
machine_limits_usage = emit_to_gcode
machine_max_acceleration_e = 3000,800
machine_max_acceleration_extruding = 1500,800
machine_max_acceleration_retracting = 2000,800
machine_max_acceleration_x = 1500,800
machine_max_acceleration_y = 1500,800
machine_max_acceleration_z = 1500,800
machine_max_feedrate_e = 60,30
machine_max_feedrate_x = 200,150
machine_max_feedrate_y = 200,150
machine_max_feedrate_z = 200,150
machine_max_jerk_e = 5,5
machine_max_jerk_x = 5,10
machine_max_jerk_y = 5,10
machine_max_jerk_z = 5,10
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.32
max_print_height = 330
min_layer_height = 0.08
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = M601
print_host =
printer_model = QQSP
printer_notes = Dont remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_FLSun\nPRINTER_MODEL_QQSP\nPRINTER_HAS_BOWDEN\n
printer_settings_id =
printer_technology = FFF
printer_variant = 0.4
printer_vendor =
printhost_apikey =
printhost_cafile =
remaining_times = 1
retract_before_travel = 2
retract_before_wipe = 70%
retract_layer_change = 0
retract_length = 6.5
retract_length_toolchange = 1
retract_lift = 0.4
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
silent_mode = 1
single_extruder_multi_material = 0
start_gcode = ;STARTGCODE\nM117 Initializing\n; Set coordinate modes\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\n; Reset speed and extrusion rates\nM200 D0 ; disable volumetric E\nM220 S100 ; reset speed\n; Set initial warmup temps\nM117 Nozzle preheat\nM104 S100 ; preheat extruder to no ooze temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM300 S40 P10 ; Bip\n; Home\nM117 Homing\nG28 ; home all with default mesh bed level\n; For ABL users put G29 for a leveling request\n; Final warmup routine\nM117 Final warmup\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM300 S440 P200 ; 1st beep for printer ready and allow some time to clean nozzle\nM300 S0 P250 ; wait between dual beep\nM300 S440 P200 ; 2nd beep for printer ready\nG4 S10 ; wait to clean the nozzle\nM300 S440 P200 ; 3rd beep for ready to start printing\n; Prime line routine\nM117 Printing prime line\n;M900 K0; Disable Linear Advance (Marlin) for prime line\nG92 E0.0; reset extrusion distance\nG1 X-54.672 Y-95.203 Z0.3 F4000; go outside print area\nG92 E0.0; reset extrusion distance\nG1 E2 F1000 ; de-retract and push ooze\nG3 X38.904 Y-102.668 I54.672 J95.105 E20.999\nG3 X54.671 Y-95.203 I-38.815 J102.373 E5.45800\nG92 E0.0\nG1 E-5 F3000 ; retract 5mm\nG1 X52.931 Y-96.185 F1000 ; wipe\nG1 X50.985 Y-97.231 F1000 ; wipe\nG1 X49.018 Y-98.238 F1000 ; wipe\nG1 X0 Y-109.798 F1000\nG1 E4.8 F1500; de-retract\nG92 E0.0 ; reset extrusion distance\n; Final print adjustments\nM117 Preparing to print\n;M82 ; extruder absolute mode\nM221 S{if layer_height<0.075}100{else}95{endif}\nM300 S40 P10 ; chirp\nM117 Print [input_filename_base]; Display: Printing started...
template_custom_gcode =
thumbnails = 16x16,260x260
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0
[print:0.20mm QUALITY FLSUN]
avoid_crossing_perimeters = 1
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.5
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 60
brim_width = 0
clip_multipart_objects = 1
compatible_printers =
compatible_printers_condition = printer_notes=~/.*PRINTER_MODEL_Q(QSP|5).*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 1500
dont_support_bridges = 1
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 80
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 45
extruder_clearance_radius = 45
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = gyroid
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 20
gap_fill_speed = 30
gcode_comments = 0
gcode_label_objects = 0
infill_acceleration = 800
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 80
inherits = 0.20mm QUALITY FLSUN
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 20
ironing_type = top
layer_height = 0.2
max_print_speed = 200
max_volumetric_speed = 0
min_skirt_length = 4
notes =
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{filament_type[0]}_{print_time}.gco
overhangs = 1
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 100
perimeters = 3
post_process =
print_settings_id =
raft_layers = 0
resolution = 0
seam_position = nearest
single_extruder_multi_material_priming = 0
skirt_distance = 5
skirt_height = 1
skirts = 2
slice_closing_radius = 0.049
small_perimeter_speed = 85%
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 90%
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.38
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 50%
top_solid_layers = 5
top_solid_min_thickness = 0.6
travel_speed = 150
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 170
wipe_tower_y = 140
xy_size_compensation = 0

[input_filename] in start_gcode gives an error when slicing in PrusaSlicer v2.7.4.
I replaced it with input_filename_base...

Thanks, fixed!